Get to know the disadvantages of speed humps!

Speed humps are some of the most important traffic control devices available on roadways today. They are used primarily for speed reduction of oncoming traffic.

Speed humps are bumps on the road that are part of the vertical deflection category of traffic-calming techniques. They are engineering measures that give a vertical displacement to all the vehicular traffic that crosses them.

While traffic-calming humps are cost-effective and common methods of achieving speed control, they still have flaws. Motorists and people in residential areas have complained about the older speed humps.

Criticisms range from induced wear and tear on their vehicles to a decrease in their livability. Transportation engineers take these factors into account along with the traffic data available.

If you’d like to know more about the pro and cons of speed humps, feel free to check here: Pros and cons of traffic-calming humps.

Rubber speed hump made of vulcanized rubber and designed with anti-slip surface

Do speed humps decrease property value?

One reason for some people disapproving of speed humps is the noise. It is quite clear that the vehicles are bound to make noise on impact while crossing a speed hump or a series of them.

This noise can create pollution in the neighbourhoods with speed humps. Again, speed humps do generate less noise than the speed bumps in the road, and their rubber counterparts are also quieter.

In addition to this, there is a bit of congestion that can be caused by speed humps if they are not implemented properly. This can also be cumbersome for the residents of the area. This is a factor where speed tables are better than speed humps.

This is another reason people avoid shifting to houses near speed breakers. The end result is that the values of properties near the speed humps decrease.

A rubber speed hump made of black recycled rubber with yellow reflective tapes for traffic management.

Do speed humps damage cars?

A major concern about all types of vertical deflections is that they damage motorized vehicles. This is because motor vehicle drivers tend to drive them quicker than recommended.

This causes an impact on the vehicle’s shocks and body, which can cause long-term structural damage. Also, those driving cars with lower ground clearances often damage the underside by going over.

This can be said in the case of the older and more traditional speed breakers. They are usually made of asphalt or concrete and don’t absorb impacts, as well as today’s rubber speed humps.

These types of bumps on the road have been complained about by residents. However, removing these permanent speed humps is time-consuming and expensive.

    An arrow that points to the contact form

    You have already read a good part of this article, 👀
    We've
    got the impression that you like it. 🙂

      👇🏻

      If YOU ARE LOOKING FOR A SPEED BUMP AND SPEED HUMP MANUFACTURER,
      FEEL FREE TO CONTACT US, WE ARE VERY HAPPY TO HELP!

      Let us contact you back!

      Name*

      Email*

      Phone

      Your message*

      Victorien Linkedin will be in charge of your request!

      In comparison to them, rubber speed humps are much more versatile. Made usually out of recycled plastic, they not only absorb the impacts better.

      But because they are bolted to the roadway, they can also be removed once their usage is no longer required. This makes them suitable for temporary applications as well.

      It should be noted that speed humps are less steep than speed bumps as they feature a lower rise. They are also designed with a flat top as compared to the speed bumps, which are rounder.

      This is one of the reasons why they are still less damaging for motor vehicles than speed bumps.

      Rubber speed hump coloured in black and yellow for traffic calming purpose

      Why are speed humps used?

      There is a multitude of reasons why speed humps are popular traffic calming measures. The concerned municipalities aim to reduce the traffic count in the area.

      To do this, it needs to deploy engineering measures to calm traffic. This means effectively reducing the overall traffic speed while compromising little on congestion.

      The speed bump is not suitable for this, and horizontal measures are too expensive; plus, they have their own disadvantages. As a result, the speed hump is used because it reduces the traffic volume, brings about low speed, and maintains the traffic flow.

      As a result of this, emergency vehicles are favoured. Hence, emergency-response ambulance drivers prefer it over most other methods.

      Speed humps are also used because of their versatility. Even concrete or asphalt speed humps can be installed by being chosen from many categories. The speed humps’ dimensions and spacing are then decided according to traffic safety needs.

      Despite making all of these choices, the cost of the speed humps isn’t altered by much, keeping the traffic control plan within the financial constraints.

      A black rubber speed hump made of recycled rubber with yellow reflective tapes for traffic management.

      Are speed humps effective?

      Speed humps are quite effective, as the 85th percentile data indicates. Speed humps slow city traffic, keeping it under 20 miles per hour. In comparison, a speed hump keeps the traffic within 15 mph.

      Either way, speed breakers discourage vehicles from unnecessary speeding and acceleration. This helps their drivers obey the speed limits and makes the area more livable.

      According to the UK government’s Local Transport Note 1/07, speed humps can slow traffic by 40pc. Testers from the Iowa Department of Transportation add to this further by stating that the speed humps can reduce collisions by 44pc.

      As a result, even the potential crashes start lacking severity, so the fatalities decrease. Speed humps are also chosen for truck routes and function well for emergency vehicles.

      Apart from collision prevention, speed humps also improve the lives of road-crossing pedestrians. They can be combined with crosswalks to improve pedestrian safety. Hence, cyclists or bicyclists are also protected from unsafe traffic conditions.

      As a result of these factors, a traffic engineer can also use humps to create a slow zone, such as a work zone or school zone.

      A black and yellow road hump is mounted on the road for traffic safety management.

      What is the standard of speed hump noise?

      Noise is quite a factor for the residents in a neighbourhood. This can be an even bigger problem for the residents if the traffic volume is larger and the street is busier.

      The noise also depends on the type of vehicles, as heavy traffic, such as buses and trucks, tend to make more noise while crossing a hump. The result is that most speed humps and undulation produce noise up to certain levels.

      The noise is based on the type of speed hump used. For example, flat-top-speed humps produce the least noise out of all humps at lower speeds.

      However, they produce the most noise at higher speeds, even more than the rounded and ramp humps. The humps tend to produce around 85-90 decibels in vehicles’ 15-20 mph range.

      In comparison, speed cushions are the least noisy, according to the Local Transport Note 1/07. Most of the speed humps in the UK conform to these sound levels.

      These findings are backed up by research in other countries, such as Sri Lanka. Their research states that they measured the sound levels between 71 and 80 decibels.

      A rubber speed hump made of black recycled rubber with yellow reflective tapes for traffic safety management.

      Conclusion

      In conclusion, the speed hump is a highly effective device. It can be found on most British roadways, and the reason for this is that it compromises between a slow traffic flow and medial amounts of congestion.

      Like all traffic calming methods, the speed hump has also received criticism. This includes noise pollution, increased vehicular wear and tear, and traffic.

      Regardless, it is noticeable that most of these issues are pointed toward the traditional speed humps that were installed decades ago. Should the UK and other European nations move towards temporary speed humps on public roads, many of these issues will be resolved?

        👇🏻

        If YOU ARE LOOKING FOR A SPEED BUMP AND SPEED HUMP MANUFACTURER,
        FEEL FREE TO CONTACT US, WE ARE VERY HAPPY TO HELP!

        Let us contact you back!

        Name*

        Email*

        Phone

        Your message*

        Victorien Linkedin will be in charge of your request!

         

        To learn more, we advise you to refer to the following pages:

        RUBBER SPEED BUMPS AND HUMPS

        WHO ARE WE?

        Are you curious about us? Do you wonder what are our know-hows and where do we manufacture our products?

        Discover below our know-how:

        Factory 1 - Rubber

        Best-selling products: Cable protectors, parking stops, speed bumps and cushions.

        Factory 2 - Metal

        Best-selling products: Crowd control barriers, cycle racks, steel bollards, and expanding barriers.

        Factory 3 - Plastic

        Best-selling products: Cable protector covers, traffic cones, roadworks beacons and posts.

        Our Factories

        LOCATIONS

        Sino Concept is a French-owned direct manufacturer with 3 factories in Qingdao, China.

        Sales offices in France, Germany, Finland, and headquarter is in Dubai.

        More about us

        Are you looking for a
        speed bump and hump manufacturer?

          Let us contact you back!

          Name*

          Email*

          Phone

          Your message*

          Victorien Linkedin will be in charge of your request!

          FOLLOW US ON LINKEDIN

          Company

          Our CEO

          CONTACT US

          If you have any questions, you can also email us at
          [email protected]

          Contact